Search results for "Flyback converter"

High-Efficiency Regulation Method for a Zero-Current and Zero-Voltage Current-Fed Push–Pull Converter

2011

A new high-efficiency regulation method for a zero-current and zero-voltage current-fed push-pull converter is presented. The method proposed is based on the use of a controlled transformer as a post-regulator, which adds or subtracts an additional voltage to the output filter of the converter. An auxiliary regulator, which only handles a percentage of the output power, controls this transformer, and therefore, results in much higher efficiency than a normal preregulator would have. The novelty of the presented converter is that regulation is achieved without affecting the zero-voltage and zero-current switching in any working conditions. Small- and large-signal models of the converter have…

Non-linear inductor modelling for a DC/DC buck converter

2017

The paper is focused on the modelling of an inductor to exploit its non-linear behaviour in the roll-off region when it is employed in a DC/DC converter. The model is set up on the basis of experimental data measured in operating conditions, which are fitted to a polynomial curve describing the inductance variations. The analysis of the buck converter, performed by including the proposed model, is validated by experimental tests.

DC/DC converter topologies for electrolyzers: State-of-the-art and remaining key issues.

2017

In recent years, the use of electrolyzers to produce cleanly and efficiently hydrogen from renewable energy sources (i.e. wind turbines, photovoltaic) has taken advantage of a growing interest from researchers and industrial. Similarly to fuel cells, DC/DC converters are needed to interface the DC bus with the electrolyzer. Usually, electrolyzers require a low DC voltage to produce hydrogen from water. For this reason, a DC/DC buck converter is generally used for this purpose. However, other DC/DC converter topologies can be used depending on the feature of the electrolyzer and electrical grid as well. The main purpose of this paper is to present the current state-of-the-art of DC/DC conver…

An improved Flyback converter

2009

This paper presents a modified Flyback converter able to operate with higher efficiency and smaller size, overcoming most of the conventional flyback converter drawbacks, and also keeping its low cost and simplicity. In particular, the proposed converter allows the mosfet off voltage to be reduced and clamped to the input, thus recovering the transformer leakage energy. As a consequence, the duty cycle can be extended to unity, thus reducing the voltage stress across the output rectifier, and lowering both the magnetizing inductance and the transformer bias current values. In addition, due to the auxiliary mosfet, the magnetizing current can become negative, eliminating the discontinuous co…

A lossless current sensing technique for flyback converters

2009

Regardless of the feedback control, almost all converters require input or output current sense for overcurrent protection. If a current mode control is implemented, high accuracy is also required. The optimal current sensing method shows the highest accuracy and the lowest power dissipation. In this paper, a lossless and accurate current sensing technique for Flyback converters is proposed. An RC network is parallel connected with the primary MOSFET and the voltage signal across the sense capacitor accurately reproduces the magnetizing current waveform. The RC technique benefits from all the advantages of the most common current sensing techniques currently applied to Flyback converters, a…

A topology for multiple generation system with doubly fed induction machines and indirect matrix converter.

2008

In this paper, a new topology for a grid connected generation system based on two double fed induction generators is presented The scheme uses an indirect matrix converter consisting on an input rectifier, a three-to-two matrix converter which provides a DC voltage, and two voltage fed output converters. The input converter is connected to the grid and each of the output converters is connected to the rotor of the corresponding machine. The rotor currents of each generator are vector controlled and unity power factor operation at the indirect matrix converter input is considered. The duty cycles for the input converter are chosen in order to obtain maximum DC link voltage. The duty cycles f…

Dynamic modelling of a quadratic DC/DC single-switch boost converter

2017

This manuscript proposes the analysis of a Quadratic Boost Converter (QBC) transformer-less single switch typology. The state space average dynamic model and a constrained state space average model taking into account the mono-directional components of the converter (diodes, switches) have been analyzed. The static gain expression taking into consideration the parasitic elements of the converter and the small-signal transfer function of the QBC typology under study has been obtained. A sensitivity analysis has shown a high variation of the gain versus duty-cycle and of the derivative gain versus parasitic parameters of the converter in the range of the duty-cycle from 0.6 to 0.8 which is ra…

Stability improvement of isolated multiple-output DC/DC converter using coupled inductors

2016

Coupling output inductors is a very popular solution when designing a multiple-output DC/DC system. Space-borne circuits are one of the areas where a custom DC/DC converter design with coupled inductors could be preferred to have a detailed design of all variables. Output voltage regulation can be improved using coupled output inductors on a multiple-output DC/DC converter, and, as demonstrated in this paper, it provides an enhanced stability. This paper presents the small signal analysis of a push-pull converter with seven outputs having all its output inductors coupled together and compares it theoretically to the uncoupled version to demonstrate the stability improvement. The theoretical…

A lossles current sensing technique for flyback converters

2009

Identification and Robust Control of a Quadratic DC/DC Boost Converter by Hammerstein Model

2015

This paper deals with the theoretical framework definition and the experimental application of the Hammerstein (HM) identification and related robust control technique to a quadratic dc/dc single-switch boost (Q-boost) converter. A set of fourth-order transfer functions (TFs) has been identified with the Hammerstein approach, on the basis of a pseudorandom-binary-sequence (PRBS) excitation signal. The set of identified TFs has been then used to design a suitable robust control technique, able to properly deal with the converter parameter uncertainty and load variations. The proposed approach has been tested in numerical simulation and validated experimentally on a suitably developed test se…